Milan Technology MIL-SM2401MAF Manual do Utilizador

MIL-SM2401MAF 24-Port 10/100 BASE-TX POE Two combo ports 10/100/1000BASE-T/1000Base-X SFP Advanced Managed Switch User Guide

2  Support Port Based V LAN /802 .1Q Tag VLAN  Support IEEE802.3a

92 SNMP Configuration interface SNMP System Options 1. Press <

93 SNMP System Options interface Community Strings  Add Communi

94 Add Community Strings interface  Edit SNMP Community 1. Sele

95 by the switch. If no trap manager is defined, no traps will issue.

96 exchanging information between Partner Systems on a link to allow

97 [Note] Before set LACP support, you have to set trunk gr

98 LACP State Activity configuration interface LACP Group Status Wh

99 You can enable or disable the IGMP/GVRP (GARP VLAN Registration Pr

100 802.1x Configuration interface 802.1x Setup 1. Select <E

101 802.1x Setup interface System Configuration After enabling

3 RFC Standard RFC 2030 SNTP, RFC 2821 SMTP (option), RFC 1492 TACACS

102 802.1x System Configuration interface Per Port Setting The St

103 802.1x Per Port Setting interface Misc Configuration 1. Sele

104 802.1x Misc Configuration interface

105 System Reset Configuration System Reset Configuration interface

106 Factory Default interface System Reboot Reboot the switch in so

107 UPS information display  I/P Volt.: display the current valu

108 [8] Turn ON/OFF Beeper Turn on the UPS beeper or turn off the UPS

109  Port Enable: displays the POE port status. Y means the por

110  Overload: It means the current is over the PD current classifi

111 [3]. Set Port PwrLimitClass. (ON/OFF) Enabling or disabling per p

4 IGMP It supports IGMP snooping for multimedia application and suppo

112 Save Configuration Interface Xmodem Upgrade Before using Xmo

113 6. After successfully upgraded the new firmware, please modif

114 Web-Based Management The Web-Based Management offers advanced ma

115 System Login 1. Launch the Internet Explorer. 2. Type “http:/

116 configured. “Actual” means the current value of the port. 5. Flo

117 Port information interface Port Statistics The following inf

118 Port Statistics interface Administrator In Administrator func

119 IP Address User can configure the IP Settings and DHCP client

120 In Switch setting, it has three parts of setting – Basic, Advance

121 In Advanced setting, it has two sections – MAC Table Address Entr

5 Fault status detect Null: no PD present Overload: current support o

122 Switch Advanced setting interface  Priority Queue Service set

123 Misc Configuration  Collisions Retry Forever: disable is in ha

124 Console Port Information Console is a standard UART interfa

125 8. Band Width: The port1 ~ port 26, supports port ingress and eg

126 Trunking The Link Aggregation Control Protocol (LACP) provi

127 7. Click Apply. 8. Use Delete button to delete Trunk Group

128 Aggregator State Activity When you had setup the LACP aggregat

129 Trunking – State Activity interface Forwarding and Filtering

130 Message Description Query A message sent from the querier (IGM

131 Static MAC Address When you add a static MAC address, it remains

6 Package Contents Unpack the contents of the 24 10/100TX plus 2 SF

132 MAC filtering MAC address filtering allows the switch to drop u

133 same VLAN members. Basically, creating a VLAN from a switch is lo

134 Port-based VLAN Packets can go among only members of the same VL

135 VLAN—PortBase Add interface 3. Enter the VLAN name, VLAN ID an

136 5. You will see the VLAN displays. 6. If there are many groups

137 You can create Tag-based VLAN, and enable or disable GVRP protoco

138  Basic 1. Click Add button. 802.1q VLAN –Add interface 2.

139 6. Click Next. Then you will see the page as follow.

140 7. To set the outgoing frames are VLAN-Tagged frames or

141 3. Acceptable Frame type:  ALL: Acceptable all Packet  Tag O

7 Hardware Description This chapter describes the hardware of

142 System Configuration 1. You can view spanning tree information

143 Per Port Configuration You can configure path cost and priority

144 SPT – Per Port Configuration interface Port Mirroring The Po

145 will be duplicated into mirror port. 1. Port Mirroring State: se

146 Prot Mirroring interface SNMP Management The SNMP is a Protocol

147 You can define management stations as trap managers and to enter

148 information. 3. RW: Read write. Enables requests accompanied b

149 SNTP Configuration You can configure the SNTP (Simple Network T

150 2. Server Port: set the UDP destination port for authentication

151 Supplicant and the authentication server.  Disable: The specifie

8 LED statuses and meaning. LED indicators LED Status Descri

152 authentication session. 3. Supplicant timeout: Set the period of

153 System Log Interface Save Configuration You must save the con

154 Save Configuration Interface TFTP Update Firmware It provides

155 TFTP Restore Configuration You can restore EEPROM value from TFT

156 TFTP Backup Configuration interface Factory Default Reset Swi

157 System Reboot interface Power Status You can view connected U

158  Output Voltage: display the current value, minimum, and

159 POE Status Interface  Power Management: Enabling or disab

160 (High), 3 = L (Low).  Power Limit Max (mW) (<15400): Set the

161 Troubleshooting This section is intended to help you solve the

9 Green The POE Injector function is on and power is forwarding the a

162  Improper Network Topologies It is important to make sure that

163 make sure the power pair it uses. The following table is the sign

164 OR (VCC-)1 1 (VCC-) (VCC-)2

165 Technical Specification This section provides the specifica

166 RS-232 connector One RS-232 DB-9 female connector for switch mana

167 Ventilation 2 DC Fans with detect function Operating environment

168 Appendix Console Port Pin Assignments The DB-9 serial port on

169 3 TXD -----------TXD ----------> 2 RxD 5 SGND -----------SG

170 Pin Number Assignment 1 Tx+ 2 Tx- 3 Rx+ 6 Rx- Note: “+” and

10 Rear Panel The two fans, two console ports, and the 3-pronged powe

11 with the smaller bracket screws. Then attach the remaining bracket

Regulatory Approval - FCC Class A - UL 1950 - EN60950 - CE - EN5502

12 Network Application PC, workstations, Wireless Access Points and

13 Segment workgroup For enterprise networks where large data b

14 Power over Ethernet Application DC Power Input The 24 10/100

15

16 Power Redundant The 24 10/100TX plus one Exp. slot ma

17 Power Redundant Application

18 Console Management Connecting to the Switch The console por

19 Enter key to bring out the login prompt. Key in the “root“(default

20 your switch. level are a subset of those available at the privile

21 Interface configuration Enter the interface command (with a specif

FCC Warning This Equipment has been tested and found to comply with

22 system location [word] Global configuration mode Set switch system

23 default Global configuration mode Restore to default Switch (con

24 show ip Privileged EXEC Show IP information Switch# show ip addr

25 Use the duplex configuration command to specify the duplex mode of

26  The 1000Base-FX module only supported for speed 1000 & auto

27 Bandwidth [in | out] [value] Interface configuration mode Set band

28 show interface status Interface configuration mode show interface

29 show group [group-ID] Privileged EXEC mode Display trunk group i

30  VLAN Commands Set Commands Command Level Description Defaults E

31 vlan [Group name] delete [port ID] VLAN database mode Remove the p

i Contents CE Mark Warning ... iii INTRODUC

32 vlanid [group ID] port [port ID] tag [port ID] IP-ip ARP-arp Ap

33 range] mode [256~511] range 1 [512~767] range 2 [768~1023] range

34 untagged] VLAN protocol [Group name] delete [port ID] VLAN databas

35 show port [port ID] VLAN database mode show Port PVID and Ingress

36 spanning-tree [on / off] or no spanning-tree Global configurati

37 switch does not receive a bridge protocol data unit (BPDU) message

38 stp-path-cost [number] Interface configuration mode Use the spanni

39 long each of the listening and learning states last before the por

40 qos storm-control [5|10|15|20|25| off (%)] or no storm-control G

41 qos queuepolicy [Policy] hi [number] low [number] Global configura

ii  Port Commands Set...24  Trunk Commands Set ...

42 show qos policy Global configuration mode Show qos policy Switch

43 IP VID Port 224.1.1.1 10 1,2,6 

44 mac-address-table table [static | filter] hwaddr [MAC address] vl

45 the MAC address table. aging-time: 300

46  SNMP Commands Set Commands Command Level Description Defaults

47 No snmp-server host [IP address] community [word] Switch(confi

48 show port monitor Privileged EXEC mode Use the show port monitor

49 8021x system radiusip [IP address] Or no 8021x system radiusip G

50 8021x misc quietperiod [sec.] Or no 8021x misc quietperiod Global

51 authentication fails and the authentication session ends. 8021x mi

iii Protocol Related Configuration...88 STP Configuration ...

52 authentication server.  Disable: The specified port is required

53 address] [file name] Server IP:192.168.1.1 Image Filename:image.

54 status POE mode Show POE information Switch(poe)# status setpm

55 portleg [enable | disable] [ports] POE mode Enabling or disablin

56  SNTP Commands Set Commands Command Level Description Defaults

57 Menu Management After you login to the system, you will s

58 Main menu line interface  Control Key description: The control

59 Status and Counters In Status and Counters, you can view Port sta

60  BP: display backpressure status.  Bandwidth In/Out: display b

61 Port counter information interface System Information • It displ

iv Aggregator State Activity...128 Forwarding and Filtering...

62 System Information interface

63 Switch Configuration In Switch Configuration, it has 8 main

64 Administration Configuration main interface Device Information

65 Device Information interface IP Configuration You can configur

66 IP Configuration interface User Name Configuration You can ch

67 User Name Configuration interface Password Configuration You c

68 Password Configuration interface SNTP Configuration You can co

69 SNTP Configuration Interface System log Client Configuration Y

70 System log Client Configuration Interface Port Configuration Y

71 Port Configuration interface Trunk Configuration You can confi

v  Improper Network Topologies ...162 Diagnosing LED Indicators ...

72 Trunk Configuration interface Port Mirroring Configuration The

73 Port Mirroring interface 3. Analysis port: Set the destination

74 VLAN Configuration You can configure VLAN group in VLAN Configura

75  Ingress Filter: It matches that Ingress Filtering Rule 2 on web

76 4. Member: Press ”Space” key to change the member value. There ar

77 2. Select <Edit>. 3. VLAN Name: Type a name for the new

78 Create VLAN Group: 802.1Q interface Edit / Delete VLAN Group U

79 Edit/Delete a VLAN Group interface Group Sorted Mode You can s

80 Group Sorted Mode interface

81 Priority Configuration You can configure port priority level. The

1 Introduction The 24 10/100TX plus 2 SFP/Copper managed POE switch is a multi-port Switch that can be used to build high-performance switched

82 Priority Configuration interface MAC Address Configuration Whe

83 MAC Address Configuration interface

84 Static MAC Address  Add the Static MAC Address You can add stat

85 1. Press <Delete> key. 2. Choose the MAC address that you

86 4. Press “ESC” to go back action menu line 5. Select <Apply&g

87  Collisions Retry Forever: Disable In half duplex, if happen col

88 Protocol Related Configuration You can configure Spanning Tre

89 STP Configuration interface STP Setup You must enable Spanning T

90 System Configuration You can configure the STP system parameter

91 root port. 4. Press “ESC” goes back action menu line. 5. Select